Man Pages in
sg3-utils
Carta.tech
Packages
sg3-utils
67
Section 8:
System administration commands
rescan-scsi-bus.sh.8
Script for adding and removing scsi devices without rebooting
scsi_logging_level.8
Access linux scsi logging level information
scsi_mandat.8
Check scsi device support for mandatory commands
scsi_readcap.8
Do scsi read capacity command on disks
scsi_ready.8
Do scsi test unit ready on devices
scsi_satl.8
Check scsi to ata translation (sat) device support
scsi_start.8
Start one or more scsi disks
scsi_stop.8
Stop (spin down) one or more scsi disks
scsi_temperature.8
Fetch the temperature of a scsi device
sg3_utils.8
A package of utilities for sending scsi commands
sg_compare_and_write.8
Send the scsi compare and write command
sg_copy_results.8
Send scsi receive copy results command (xcopy related)
sg_dd.8
Copy data to and from files and devices, especially scsi devices
sg_decode_sense.8
Decode scsi sense data
sg_emc_trespass.8
Change ownership of scsi lun from another service-processor to this one
sg_get_config.8
Send scsi get configuration command (mmc-4 +)
sg_get_lba_status.8
Send scsi get lba status command
sg_ident.8
Send scsi report/set identifying information command
sg_inq.8
Issue scsi inquiry command and/or decode its response
sg_logs.8
Access log pages with scsi log sense command
sg_luns.8
Send scsi report luns command or decode given lun
sg_map.8
Displays mapping between linux sg and other scsi devices
sg_map26.8
Map scsi generic (sg) device to corresponding device names
sg_modes.8
Reads mode pages with scsi mode sense command
sg_opcodes.8
Report supported scsi commands or task management functions
sg_persist.8
Use scsi persistent reserve command to access registrations and reservations
sg_prevent.8
Send scsi prevent allow medium removal command
sg_raw.8
Send arbitrary scsi command to a device
sg_rbuf.8
Reads data using scsi read buffer command
sg_rdac.8
Display or modify scsi rdac redundant controller mode page
sg_read.8
Read multiple blocks of data, optionally with scsi read commands
sg_read_block_limits.8
Send scsi read block limits command
sg_read_buffer.8
Send scsi read buffer command
sg_read_long.8
Send a scsi read long command
sg_readcap.8
Send scsi read capacity command
sg_reassign.8
Send scsi reassign blocks command
sg_referrals.8
Send scsi report referrals command
sg_rep_zones.8
Send scsi report zones command
sg_requests.8
Send one or more scsi request sense commands
sg_reset.8
Sends scsi device, target, bus or host reset; or checks reset state
sg_reset_wp.8
Send scsi reset write pointer command
sg_rmsn.8
Send scsi read media serial number command
sg_rtpg.8
Send scsi report target port groups command
sg_safte.8
Access scsi accessed fault-tolerant enclosure (saf-te) device
sg_sanitize.8
Remove all user data from disk with scsi sanitize command
sg_sat_identify.8
Send ata identify device command via scsi to ata translation (sat) layer
sg_sat_phy_event.8
Use ata read log ext via a sat pass-through to fetch sata phy event counters
sg_sat_set_features.8
Use ata set features command via a scsi to ata translation (sat) layer
sg_scan.8
Scans sg devices (or scsi/atapi/ata devices) and prints results
sg_senddiag.8
Performs a scsi send diagnostic command
sg_ses.8
Access a scsi enclosure services (ses) device
sg_start.8
Send scsi start stop unit command: start, stop, load or eject medium
sg_stpg.8
Send scsi set target port groups command
sg_sync.8
Send scsi synchronize cache command
sg_test_rwbuf.8
Test a scsi host adapter by issuing dummy writes and reads
sg_turs.8
Send one or more scsi test unit ready commands
sg_unmap.8
Send scsi unmap command (known as 'trim' in ata specs)
sg_verify.8
Invoke scsi verify command(s) on a block device
sg_vpd.8
Fetch scsi vpd page and/or decode its response
sg_wr_mode.8
Write (modify) scsi mode page
sg_write_buffer.8
Send scsi write buffer commands
sg_write_long.8
Send scsi write long command
sg_write_same.8
Send scsi write same command
sg_xcopy.8
Copy data to and from files and devices using scsi extended copy (xcopy)
sginfo.8
Access mode page information for a scsi (or atapi) device
sgm_dd.8
Copy data to and from files and devices, especially scsi devices
sgp_dd.8
Copy data to and from files and devices, especially scsi devices