multipath.conf (5)

multipath.conf is the configuration file for the multipath daemon. It is used to overwrite the built-in configuration table of multipathd. Any line whose first non-white-space character is a '#' is considered a comment line. Empty lines are ignored.

The configuration file contains entries of the form:

<section> {
<attribute> <value>
...
<subsection> {
<attribute> <value>
...

} }

Each section contains one or more attributes or subsections. The recognized keywords for attributes or subsections depend on the section in which they occur.

The following section keywords are recognized:

defaults

This section defines default values for attributes which are used whenever no values are given in the appropriate device or multipath sections.

blacklist

This section defines which devices should be excluded from the multipath topology discovery.

blacklist_exceptions

This section defines which devices should be included in the multipath topology discovery, despite being listed in the blacklist section.

multipaths

This section defines the multipath topologies. They are indexed by a World Wide Identifier(wwid), which is taken to be the value of the udev attribute given by the uid_attribute keyword.

devices

This section defines the device-specific settings.

The defaults section recognizes the following keywords:

polling_interval

interval between two path checks in seconds. For properly functioning paths, the interval between checks will gradually increase to max_polling_interval. This value will be overridden by the WatchdogSec setting in the multipathd.service definition if systemd is used. Default is 5

max_polling_interval

maximal interval between two path checks in seconds; default is 4 * polling_interval

multipath_dir

directory where the dynamic shared objects are stored; default is system dependent, commonly /lib/multipath

verbosity

default verbosity. Higher values increase the verbosity level. Valid levels are between 0 and 6; default is 2

reassign_maps

enable reassigning of device-mapper maps. With this option multipathd will remap existing device-mapper maps to always point to multipath device, not the underlying block devices. Possible values are yes and no. Default is yes

path_selector

The default path selector algorithm to use; they are offered by the kernel multipath target. There are three selector algorithms.

round-robin 0

Loop through every path in the path group, sending the same amount of IO to each.

queue-length 0

Send the next bunch of IO down the path with the least amount of outstanding IO.

service-time 0

Choose the path for the next bunch of IO based on the amount of outstanding IO to the path and its relative throughput.

path_grouping_policy

The default path grouping policy to apply to unspecified multipaths. Possible values are

failover

1 path per priority group

multibus

all paths in 1 priority group

group_by_serial

1 priority group per serial number

group_by_prio

1 priority group per priority value. Priorities are determined by callout programs specified as a global, per-controller or per-multipath option in the configuration file.

group_by_node_name

1 priority group per target node name. Target node names are fetched in /sys/class/fc_transport/target*/node_name.

Default value is failover.

uid_attribute

The udev attribute providing a unique path identifier. Default value is ID_SERIAL

getuid_callout

The default program and args to callout to obtain a unique path identifier. Should be specified with an absolute path. This parameter is deprecated; uid_attribute should be used instead.

prio

The name of the path priority routine. The specified routine should return a numeric value specifying the relative priority of this path. Higher number have a higher priority. none is a valid value. Currently the following path priority routines are implemented:

const

Return a constant priority of 1.

emc

Generate the path priority for EMC arrays.

alua

Generate the path priority based on the SCSI-3 ALUA settings.

ontap

Generate the path priority for NetApp arrays.

rdac

Generate the path priority for LSI/Engenio/NetApp E-Series RDAC controller.

hp_sw

Generate the path priority for Compaq/HP controller in active/standby mode.

hds

Generate the path priority for Hitachi HDS Modular storage arrays.

random

Generate a random priority between 1 and 10.

weightedpath

Generate the path priority based on the regular expression and the priority provided as argument. requires prio_args keyword.

Default value is none.

prio_args

Arguments to pass to to the prio function. Currently only used with weighted, which needs a value of the form <hbtl|devname> <regex1> <prio1> <regex2> <prio2> ... hbtl regex can be of SCSI H:B:T:L format Ex: 1:0:.:. , *:0:0:. devname regex can be of device name format Ex: sda , sd.e

features

Specify any device-mapper features to be used. Syntax is num list where num is the number of features in list. Possible values for the feature list are

queue_if_no_path

Queue IO if no path is active; identical to the no_path_retry keyword.

no_partitions

Disable automatic partitions generation via kpartx.

path_checker

The default method used to determine the paths state. Possible values are

readsector0

(Deprecated) Read the first sector of the device. This checker is being deprecated, please use directio instead

tur

Issue a TEST UNIT READY command to the device.

emc_clariion

Query the EMC Clariion specific EVPD page 0xC0 to determine the path state.

hp_sw

Check the path state for HP storage arrays with Active/Standby firmware.

rdac

Check the path state for LSI/Engenio/NetApp E-Series RDAC storage controller.

directio

Read the first sector with direct I/O.

Default value is directio.

failback

Tell multipathd how to manage path group failback.

immediate

Immediately failback to the highest priority pathgroup that contains active paths.

manual

Do not perform automatic failback.

followover

Only perform automatic failback when the first path of a pathgroup becomes active. This keeps a node from automatically failing back when another node requested the failover.

values > 0

deferred failback (time to defer in seconds)

Default value is manual.

rr_min_io

The number of IO to route to a path before switching to the next in the same path group. This is only for BIO based multipath. Default is 1000

rr_min_io_rq

The number of IO requests to route to a path before switching to the next in the same path group. This is only for request based multipath. Default is 1

rr_weight

If set to priorities the multipath configurator will assign path weights as "path prio * rr_min_io". Possible values are priorities or uniform. Default is uniform.

no_path_retry

Specify the number of retries until disable queueing, or fail for immediate failure (no queueing), queue for never stop queueing. If unset no queueing is attempted. Default is unset.

user_friendly_names

If set to yes , using the bindings file /etc/multipath/bindings to assign a persistent and unique alias to the multipath, in the form of mpath<n>. If set to no use the WWID as the alias. In either case this be will be overridden by any specific aliases in the multipaths section. Default is no

flush_on_last_del

If set to yes , multipathd will disable queueing when the last path to a device has been deleted. Default is no

max_fds

Specify the maximum number of file descriptors that can be opened by multipath and multipathd. This is equivalent to ulimit -n. A value of max will set this to the system limit from /proc/sys/fs/nr_open. If this is not set, the maximum number of open fds is taken from the calling process. It is usually 1024. To be safe, this should be set to the maximum number of paths plus 32, if that number is greated than 1024.

checker_timeout

Specify the timeout to user for path checkers that issue scsi commands with an explicit timeout, in seconds; default taken from /sys/block/sd<x>/device/timeout

fast_io_fail_tmo

Specify the number of seconds the scsi layer will wait after a problem has been detected on a FC remote port before failing IO to devices on that remote port. This should be smaller than dev_loss_tmo. Setting this to off will disable the timeout.

dev_loss_tmo

Specify the number of seconds the scsi layer will wait after a problem has been detected on a FC remote port before removing it from the system. This can be set to "infinity" which sets it to the max value of 2147483647 seconds, or 68 years. It will be automatically adjusted to the overall retry interval no_path_retry * polling_interval if a number of retries is given with no_path_retry and the overall retry interval is longer than the specified dev_loss_tmo value. The linux kernel will cap this value to 300 if fast_io_fail_tmo is not set.

queue_without_daemon

If set to no , when multipathd stops, queueing will be turned off for all devices. This is useful for devices that set no_path_retry. If a machine is shut down while all paths to a device are down, it is possible to hang waiting for IO to return from the device after multipathd has been stopped. Without multipathd running, access to the paths cannot be restored, and the kernel cannot be told to stop queueing IO. Setting queue_without_daemon to no , avoids this problem. Default is yes

bindings_file

The full pathname of the binding file to be used when the user_friendly_names option is set. Defaults to /etc/multipath/bindings

wwids_file

The full pathname of the wwids file, which is used by multipath to keep track of the wwids for LUNs it has created multipath devices on in the past. Defaults to /etc/multipath/wwids

log_checker_err

If set to once , multipathd logs the first path checker error at logging level 2. Any later errors are logged at level 3 until the device is restored. If set to always , multipathd always logs the path checker error at logging level 2. Default is always

reservation_key

This is the service action reservation key used by mpathpersist. It must be set for all multipath devices using persistent reservations, and it must be the same as the RESERVATION KEY field of the PERSISTENT RESERVE OUT parameter list which contains an 8-byte value provided by the application client to the device server to identify the I_T nexus. It is unset by default.

retain_attached_hw_handler

If set to yes and the scsi layer has already attached a hardware_handler to the device, multipath will not force the device to use the hardware_handler specified by mutipath.conf. If the scsi layer has not attached a hardware handler, multipath will continue to use its configured hardware handler. Default is no

detect_prio

If set to yes , multipath will try to detect if the device supports ALUA. If so, the device will automatically use the alua prioritizer. If not, the prioritizer will be selected as usual. Default is no

The blacklist section is used to exclude specific device from inclusion in the multipath topology. It is most commonly used to exclude local disks or LUNs for the array controller.

The following keywords are recognized:

wwid

The World Wide Identification of a device.

devnode

Regular expression of the device nodes to be excluded.

property

Regular expression of the udev property to be excluded.

device

Subsection for the device description. This subsection recognizes the vendor and product keywords. For a full description of these keywords please see the devices section description.

The blacklist_exceptions section is used to revert the actions of the blacklist section, ie to include specific device in the multipath topology. This allows one to selectively include devices which would normally be excluded via the blacklist section.

The following keywords are recognized:

wwid

The World Wide Identification of a device.

property

Regular expression of the udev property to be whitelisted. Defaults to (ID_WWN|ID_SCSI_VPD)

devnode

Regular expression of the device nodes to be whitelisted.

device

Subsection for the device description. This subsection recognizes the vendor and product keywords. For a full description of these keywords please see the devices section description.

The property blacklist and whitelist handling is different from the usual handling in the sense that the whitelist has to be set, otherwise the device will be blacklisted. In these cases the message blacklisted, udev property missing will be displayed.

The only recognized attribute for the multipaths section is the multipath subsection.

The multipath subsection recognizes the following attributes:

wwid

Index of the container. Mandatory for this subsection.

alias

(Optional) symbolic name for the multipath map.

The following attributes are optional; if not set the default values are taken from the defaults or devices section:

path_grouping_policy

path_selector

prio

prio_args

failback

rr_weight

flush_on_last_del

no_path_retry

rr_min_io

rr_min_io_rq

features

reservation_key

The only recognized attribute for the devices section is the device subsection.

The device subsection recognizes the following attributes:

vendor

(Mandatory) Vendor identifier

product

(Mandatory) Product identifier

revision

(Optional) Revision identfier

product_blacklist

(Optional) Product strings to blacklist for this vendor

alias_prefix

(Optional) The user_friendly_names prefix to use for this device type, instead of the default "mpath"

hardware_handler

(Optional) The hardware handler to use for this device type. The following hardware handler are implemented:

1 emc

Hardware handler for EMC storage arrays.

1 rdac

Hardware handler for LSI/Engenio/NetApp E-Series RDAC storage controller.

1 hp_sw

Hardware handler for Compaq/HP storage arrays in active/standby mode.

1 alua

Hardware handler for SCSI-3 ALUA compatible arrays.

The following attributes are optional; if not set the default values are taken from the defaults section:

path_grouping_policy

uid_attribute

path_selector

path_checker

prio

prio_args

features

failback

rr_weight

no_path_retry

rr_min_io

rr_min_io_rq

fast_io_fail_tmo

dev_loss_tmo

flush_on_last_del

retain_attached_hw_handler

detect_prio

The usage of queue_if_no_path option can lead to D state processes being hung and not killable in situations where all the paths to the LUN go offline. It is advisable to use the no_path_retry option instead.

The use of queue_if_no_path or no_path_retry might lead to a deadlock if the dev_loss_tmo setting results in a device being removed while I/O is still queued. The multipath daemon will update the dev_loss_tmo setting accordingly to avoid this deadlock. Hence if both values are specified the order of precedence is no_path_retry, queue_if_no_path, dev_loss_tmo

udev(8), dmsetup(8) multipath(8) multipathd(8)

multipath was developed by Christophe Varoqui, <[email protected]> and others.