pnmpad1

Usage

Overview

This program is part of Netpbm(1) .

pnmpad reads a Netpbm image as input and outputs a PNM image that is the input image plus borders of the color and sizes specified.

You can use pamcomp to add borders of any content - solid color,
pattern, or whatever. For example, if you wanted to add 10 pixels of
rainbow borders to the top and bottom of a 100x100 image, you could create a
100x120 rainbow image (e.g. with ppmrainbow) and then
use pamcomp to insert your 100x100 image into the center of it.

Options

In addition to the options common to all programs based on libnetpbm (most notably -quiet, see
Common Options ⟨index.html#commonoptions⟩ ), pnmpad recognizes the following command line options:

All options can be abbreviated to their shortest unique prefix. You may use two hyphens instead of one to designate an option. You may use either white space or an equals sign between an option name and its value.

-color=color

-detect-background

-extend-edge

-white

-black

This specifies the color of the padding. color is like the argument of the pnm_parsecolor() library routine ⟨libnetpbm_image.html#colorname⟩ .

-detect-background means the program uses the color of the top left pixel of the input as the pad color. Note that this could cause odd results if you aren't padding the top or left of the image.

You may specify only one of -white, -black, -color, and -detect-background.

-extend-edge says to pad by duplicating the adjacent edge of the image pixel by pixel. E.g. if the top row of the image is 20 white pixels followed by 10 black pixels, every row of padding added to the top of the image is 20 white pixels followed by 20 black pixels.

By default, the padding is black.

-white and -black are for backward compatibility; they do the same thing as -color=white and -color=black respectively (except that the latter fail if you don't have a color dictionary set up in your environment, so they are really more like -color=rgbi:0/0/0 and -color=rgbi:1/1/1. -color, -detect-background, and -extend-edge were new with Netpbm 11.05 (December 2023).

-left=pixels

-right=pixels

-width=width

-halign=ratio

-mwidth=pixels

Specify amount of left and right padding in pixels.

-left and -right directly specify the amount of padding added to the left and right sides, respectively, of the image.

Alternatively, you can specify -width and just one of -left and -right and pnmpad calculates the required padding on the other side to make the output width pixels wide. If the -width value is less than the width of the input image plus the specified padding, pnmpad ignores -width.

If you specify all three of -width, -left, and -right, you must ensure that the -left and -right padding are sufficient to make the image at least as wide as -width specifies, and in that case -width has no effect on the output. Otherwise, pnmpad fails.

When you specify -width without -left or -right, and -width is larger than the input image, pnmpad chooses left and right padding amounts in a certain ratio. That ratio defaults to half, but you can set it to anything (from 0 to 1) with the -halign option. If the input image is already at least as wide as -width specifies, pnmpad adds no padding.

Common values for -halign are:

0.0

left aligned

0.5

center aligned (default)

1.0

right aligned

-mwidth=pixels says to pad to a multiple of pixels pixels. E.g. if pixels is 10, the output image width will be a multiple of 10 pixels. pnmpad adds to whatever padding the other options say to do to get to this multiple. It divides that padding between the left and right sides of the image to maintain the ratio the other options produce. E.g. if you say -left=10 -right=10 -mwidth=50 with a 100-pixel image, you end up with a 150-pixel image with the extra padding split evenly between left and right for a total of 25 pixels of padding on the left and 25 on the right. If the other options indicate no padding, pnmpad adds padding in the ratio specified by -halign and if -halign is not specified, equally on both sides.

Before Netpbm 10.97 (December 2021), pnmpad does not allow -halign with -mwidth and adds padding only on the right when -mwidth is specified and the other options indicate no padding.

Before Netpbm 10.72 (September 2015), there is no -mwidth.

Before Netpbm 10.23 (July 2004), pnmpad did not allow the -left or -right option together with -width.

-top=pixels

-bottom=pixels

-height=height

-valign=ratio

-mheight=pixels

These options determine the vertical padding. They are analogous to the horizontal padding options above.

-promote={none|format|all}

This option tells what to do when the -color option specifies a color that cannot be represented in the input format, which ordinarily is also the output format. For example, if the input is PGM (which can represent only shades of gray), and you specify -color=red, should pnmpad make the padding gray or make the output PPM?

none

Make the output have the same format and maxval as the input.
Adjust the pad color to the nearest color possible in that format
(black, white, or a shade of gray).

format

Make the output have the same maxval as the input, but make
the output format PPM if the pad color is not black, white, or gray.

all

Make the format and maxval of the output capable of representing the
pad color. Make the format the least expressive format capable of
representing the pad color. Make the maxval the larger of 255 and
the maxval of the input image.

The default is -promote=all.

Note that this promotion happens even if no actual padding happens, meaning it isn't really necessary. The promotion is based on what would be required to represent padding of the specified color.

This option is valid only when you also specify -color.

This option was new in Netpbm 11.05 (December 2023).

-reportonly

This causes pnmpad to write to Standard Output a description of the
padding it would have done instead of producing an output image. See

below ⟨#reportonly⟩ for a description of this output and ways
to use it.

This option was new in Netpbm 10.89 (December 2019).

-verbose

This causes verbose messages.

Report only

When you specify -reportonly, pnmpad does not produce an
output image. Instead, it writes to Standard Output a description of the
padding it would have done without -reportonly.

That description is one line of text, containing 6 decimal numbers of
pixels, separated by spaces:

Example:

    <span style="font-family: monospace">
      4 3 0 2 100 100
    </span>

One use for this is to make padding which is fancier than the black and
white that pnmpad can do.

In the following example, we pad an image with 10 pixels of gray all
around, without knowing the original image dimensions beforehand. We do
this by generating a gray image with pbmmake and then pasting the
subject image into the middle of it.

The example uses shell arrays, such as exist in Bash, but not Dash.

    
    pad=($(pnmpad -reportonly -left=10 -right=10 -top=10 -bottom=10 input.ppm))
    pbmmake -gray ${pad[4]} ${pad[5]} | \
      pnmpaste input.ppm ${pad[0]} ${pad[2]} -
    

Document source

This manual page was generated by the Netpbm tool 'makeman' from HTML source. The master documentation is at

http://netpbm.sourceforge.net/doc/pnmpad.html