nvme-rpmb-write-data1
Write authenticated data to an rpmb target
Usage
nvme [<global-options>]
rpmb
write-data
<device>
[{--msgfile=<data-file> | -f
<data-file>}]
[{--msg=<data> | -d
<data>}]
[{--keyfile=<key-file> | -g
<key-file>}]
[{--key=<key> | -k
<key>}]
[--address=<offset>]
[{--blocks=<512
byte
sectors> | -b
<sectors>}]
[{--target=<target-id> | -t
<target-id>}]
Overview
Supports authenticated data writing to the specified RPMB target, at the given sector offset, using the authentication key previously programmed with nvme rpmb program-key for that target.
If the requested size is not within the total size supported by the target, the request fails without being sent to the device.
The <device> parameter is mandatory and an NVMe character device (ex: /dev/nvme0) must be specified.
Options
-
-t <target>, --target=<target> -
RPMB target id. This should be one of the supported RPMB targets as reported by nvme rpmb info. If nothing is given, the default of 0 is used as the RPMB target.
-
--address=<offset> -
The address (in 512 byte sector offset from 0) to write to on the specified RPMB target.
-
-b <sectors>, --blocks=<sectors> -
The size in 512 byte sectors to write to the specified RPMB target.
-
-k <key>, --key=<key>, -g <key-file>, --keyfile=<key-file> -
Authentication key previously programmed with nvme rpmb program-key for the given target. The key can be specified on the command line using --key or -k, or read from a file using --keyfile or -g.
-
-f <data-file>, --msgfile=<data-file> -
Name of the file the data to be written is read from.
-
-d <data>, --msg=<data> -
Provides the data to be written directly on the command line, instead of reading it from a file.
Options
The following options are defined at the top-level nvme command and are available to this subcommand:
-
--dry-run -
Print the command that would be executed, but do not actually execute it.
-
--no-ioctl-probing -
Disable probing for 64-bit IOCTL support.
-
--no-retries -
Disable retry logic on transient errors.
-
-o <fmt>, --output-format=<fmt> -
Set the reporting format to normal, tabular, 'json, or binary. Only one output format may be used at a time.
-
--output-format-version=<version> -
Select the output format version. Version 1 uses the original field naming, while version 2 (default) provides more consistent and script-friendly field names. Other versions are rejected.
-
--quiet -
Suppress informational messages. Errors are still reported, and --quiet cancels any --verbose for the library log level.
-
--set-options=<key=value>[,<key=value>...] -
Set libnvme library options for this invocation. Supported keys are force-4k, mi-probe-enabled, test-base-dir and test-sysfs-dir.
-
--timeout=<ms> -
Set the timeout for the command in milliseconds. infinite or -1 waits without a time limit (0xffffffff).
-
-v, --verbose -
Increase the level of detail in the output. May be specified multiple times to further increase verbosity.
These options can also be set as machine-wide defaults in nvme-cli.conf(5). A command-line flag always overrides the file.
Examples
• Write 200 blocks of (512 bytes) from input.bin onto target 0
# nvme rpmb write-data /dev/nvme0 -t 0 -f input.bin -b 200 -k 'SecretKey'
Nvme
Part of the nvme-user suite