ip-xfrm(8)

ip-xfrm8

Transform configuration

Usage

ip [OPTIONS] xfrm {COMMAND | help}

ip xfrm XFRM-OBJECT {COMMAND | help}

XFRM-OBJECT {:= state | policy | monitor}

ip xfrm state {add | update} ID [ALGO-LIST] [mode MODE] [mark MARK [mask MASK]] [reqid REQID] [dir SA-DIR] [seq SEQ] [replay-window SIZE] [replay-seq SEQ] [replay-oseq SEQ] [replay-seq-hi SEQ] [replay-oseq-hi SEQ] [flag FLAG-LIST] [sel SELECTOR] [LIMIT-LIST] [encap ENCAP] [coa ADDR [/PLEN]] [ctx CTX] [extra-flag EXTRA-FLAG-LIST] [output-mark OUTPUT-MARK [mask MASK]] [if_id IF-ID] [offload [{crypto | packet}] dev DEV dir DIR] [tfcpad LENGTH] [pcpu-num CPUNUM]

ip xfrm state allocspi ID [mode MODE] [mark MARK [mask MASK]] [reqid REQID] [seq SEQ] [min SPI max SPI] [pcpu-num CPUNUM]

ip xfrm state {delete | get} ID [mark MARK [mask MASK]]

ip [{-4 | -6}] xfrm state deleteall [ID] [mode MODE] [reqid REQID] [flag FLAG-LIST]

ip [{-4 | -6}] xfrm state list [ID] [nokeys] [mode MODE] [reqid REQID] [flag FLAG-LIST]

ip xfrm state flush [proto XFRM-PROTO]

ip xfrm state count

ID := [src ADDR] [dst ADDR] [proto XFRM-PROTO] [spi SPI]

XFRM-PROTO {:= esp | ah | comp | route2 | hao}

ALGO-LIST := [ALGO-LIST] ALGO

ALGO {:= {enc | auth} ALGO-NAME ALGO-KEYMAT | }

auth-trunc {ALGO-NAME ALGO-KEYMAT ALGO-TRUNC-LEN | }

aead {ALGO-NAME ALGO-KEYMAT ALGO-ICV-LEN | }

comp ALGO-NAME

MODE {:= transport | tunnel | beet | ro | in_trigger}

SA-DIR {:= in | out}

FLAG-LIST := [FLAG-LIST] FLAG

FLAG {:= noecn | decap-dscp | nopmtudisc | wildrecv | icmp | af-unspec | align4 | esn}

SELECTOR := [src ADDR [/PLEN]] [dst ADDR [/PLEN]] [dev DEV] [UPSPEC]

LIMIT-LIST := [LIMIT-LIST] limit LIMIT

LIMIT {:= {time-soft | time-hard | time-use-soft | time-use-hard} SECONDS | {byte-soft | byte-hard} SIZE | {packet-soft | packet-hard} COUNT}

ENCAP := {espinudp | espinudp-nonike | espintcp} SPORT DPORT OADDR

EXTRA-FLAG-LIST := [EXTRA-FLAG-LIST] EXTRA-FLAG

EXTRA-FLAG {:= dont-encap-dscp | oseq-may-wrap}

ip xfrm policy {add | update} SELECTOR dir DIR [ctx CTX] [mark MARK [mask MASK]] [index INDEX] [ptype PTYPE] [action ACTION] [priority PRIORITY] [flag FLAG-LIST] [if_id IF-ID] [offload packet dev DEV] [LIMIT-LIST] [TMPL-LIST]

ip xfrm policy {delete | get} {SELECTOR | index INDEX} dir DIR [ctx CTX] [mark MARK [mask MASK]] [ptype PTYPE] [if_id IF-ID]

ip [{-4 | -6}] xfrm policy {deleteall | list} [nosock] [SELECTOR] [dir DIR] [index INDEX] [ptype PTYPE] [action ACTION] [priority PRIORITY] [flag FLAG-LIST]

ip xfrm policy flush [ptype PTYPE]

ip xfrm policy count

ip xfrm policy set [hthresh4 LBITS RBITS] [hthresh6 LBITS RBITS]

ip xfrm policy setdefault DIR ACTION [DIR ACTION] [DIR ACTION]

ip xfrm policy getdefault

SELECTOR := [src ADDR [/PLEN]] [dst ADDR [/PLEN]] [dev DEV] [UPSPEC]

DIR {:= in | out | fwd}

PTYPE {:= main | sub}

ACTION {:= allow | block}

FLAG-LIST := [FLAG-LIST] FLAG

FLAG {:= localok | icmp}

LIMIT-LIST := [LIMIT-LIST] limit LIMIT

LIMIT {:= {time-soft | time-hard | time-use-soft | time-use-hard} SECONDS | {byte-soft | byte-hard} SIZE | {packet-soft | packet-hard} COUNT}

TMPL-LIST := [TMPL-LIST] tmpl TMPL

TMPL := ID [mode MODE] [reqid REQID] [level LEVEL]

ID := [src ADDR] [dst ADDR] [proto XFRM-PROTO] [spi SPI]

XFRM-PROTO {:= esp | ah | comp | route2 | hao}

MODE {:= transport | tunnel | beet | ro | in_trigger}

LEVEL {:= required | use}

LISTofXFRM-OBJECTS := [LISTofXFRM-OBJECTS] XFRM-OBJECT

XFRM-OBJECT {:= acquire | expire | SA | policy | aevent | report}

Overview

xfrm is an IP framework for transforming packets (such as encrypting their payloads). This framework is used to implement the IPsec protocol suite (with the state object operating on the Security Association Database, and the policy object operating on the Security Policy Database). It is also used for the IP Payload Compression Protocol and features of Mobile IPv6.

ip xfrm state addadd new state into xfrm
ip xfrm state updateupdate existing state in xfrm
ip xfrm state allocspiallocate an SPI value
ip xfrm state deletedelete existing state in xfrm
ip xfrm state getget existing state in xfrm
ip xfrm state deletealldelete all existing state in xfrm
ip xfrm state listprint out the list of existing state in xfrm
ip xfrm state flushflush all state in xfrm
ip xfrm state countcount all existing state in xfrm
ID

is specified by a source address, destination address, transform protocol XFRM-PROTO, and/or Security Parameter Index SPI. (For IP Payload Compression, the Compression Parameter Index or CPI is used for SPI.)

XFRM-PROTO

specifies a transform protocol: IPsec Encapsulating Security Payload (esp), IPsec Authentication Header (ah), IP Payload Compression (comp), Mobile IPv6 Type 2 Routing Header (route2), or Mobile IPv6 Home Address Option (hao).

ALGO-LIST

contains one or more algorithms to use. Each algorithm ALGO is specified by:

•

the algorithm type: encryption (enc), authentication (auth or auth-trunc), authenticated encryption with associated data (aead), or compression (comp)

•

the algorithm name ALGO-NAME (see below)

•

(for all except comp) the keying material ALGO-KEYMAT, which may include both a key and a salt or nonce value; refer to the corresponding RFC

•

(for auth-trunc only) the truncation length ALGO-TRUNC-LEN in bits

•

(for aead only) the Integrity Check Value length ALGO-ICV-LEN in bits

Encryption algorithms include ecb(cipher_null), cbc(des), cbc(des3_ede), cbc(cast5), cbc(blowfish), cbc(aes), cbc(serpent), cbc(camellia), cbc(twofish), and rfc3686(ctr(aes)).

Authentication algorithms include digest_null, hmac(md5), hmac(sha1), hmac(sha256), hmac(sha384), hmac(sha512), hmac(rmd160), and xcbc(aes).

Authenticated encryption with associated data (AEAD) algorithms include rfc4106(gcm(aes)), rfc4309(ccm(aes)), and rfc4543(gcm(aes)).

Compression algorithms include deflate, lzs, and lzjh.

MODE

specifies a mode of operation for the transform protocol. IPsec and IP Payload Compression modes are transport, tunnel, and (for IPsec ESP only) Bound End-to-End Tunnel (beet). Mobile IPv6 modes are route optimization (ro) and inbound trigger (in_trigger).

FLAG-LIST

contains one or more of the following optional flags: noecn, decap-dscp, nopmtudisc, wildrecv, icmp, af-unspec, align4, or esn.

SELECTOR

selects the traffic that will be controlled by the policy, based on the source address, the destination address, the network device, and/or UPSPEC.

UPSPEC

selects traffic by protocol. For the tcp, udp, sctp, or dccp protocols, the source and destination port can optionally be specified. For the icmp, ipv6-icmp, or mobility-header protocols, the type and code numbers can optionally be specified. For the gre protocol, the key can optionally be specified as a dotted-quad or number. Other protocols can be selected by name or number PROTO.

LIMIT-LIST

sets limits in seconds, bytes, or numbers of packets.

ENCAP

encapsulates packets with protocol espinudp, espinudp-nonike, or espintcp, using source port SPORT, destination port DPORT , and original address OADDR.

MARK

used to match xfrm policies and states

OUTPUT-MARK

used to set the output mark to influence the routing of the packets emitted by the state

IF-ID

xfrm interface identifier used to in both xfrm policies and states

DEV

Network interface name used to offload policies and states

ip xfrm policy addadd a new policy
ip xfrm policy updateupdate an existing policy
ip xfrm policy deletedelete an existing policy
ip xfrm policy getget an existing policy
ip xfrm policy deletealldelete all existing xfrm policies
ip xfrm policy listprint out the list of xfrm policies
ip xfrm policy flushflush policies
nosock

filter (remove) all socket policies from the output.

SELECTOR

selects the traffic that will be controlled by the policy, based on the source address, the destination address, the network device, and/or UPSPEC.

UPSPEC

selects traffic by protocol. For the tcp, udp, sctp, or dccp protocols, the source and destination port can optionally be specified. For the icmp, ipv6-icmp, or mobility-header protocols, the type and code numbers can optionally be specified. For the gre protocol, the key can optionally be specified as a dotted-quad or number. Other protocols can be selected by name or number PROTO.

DIR

selects the policy direction as in, out, or fwd.

CTX

sets the security context.

PTYPE

can be main (default) or sub.

ACTION

can be allow (default) or block.

PRIORITY

is a number that defaults to zero.

FLAG-LIST

contains one or both of the following optional flags: local or icmp.

LIMIT-LIST

sets limits in seconds, bytes, or numbers of packets.

TMPL-LIST

is a template list specified using ID, MODE, REQID, and/or LEVEL.

ID

is specified by a source address, destination address, transform protocol XFRM-PROTO, and/or Security Parameter Index SPI. (For IP Payload Compression, the Compression Parameter Index or CPI is used for SPI.)

XFRM-PROTO

specifies a transform protocol: IPsec Encapsulating Security Payload (esp), IPsec Authentication Header (ah), IP Payload Compression (comp), Mobile IPv6 Type 2 Routing Header (route2), or Mobile IPv6 Home Address Option (hao).

MODE

specifies a mode of operation for the transform protocol. IPsec and IP Payload Compression modes are transport, tunnel, and (for IPsec ESP only) Bound End-to-End Tunnel (beet). Mobile IPv6 modes are route optimization (ro) and inbound trigger (in_trigger).

LEVEL

can be required (default) or use.

ip xfrm policy countcount existing policies

Use one or more -s options to display more details, including policy hash table information.

ip xfrm policy setconfigure the policy hash table

Security policies whose address prefix lengths are greater than or equal policy hash table thresholds are hashed. Others are stored in the policy_inexact chained list.

LBITS

specifies the minimum local address prefix length of policies that are stored in the Security Policy Database hash table.

RBITS

specifies the minimum remote address prefix length of policies that are stored in the Security Policy Database hash table.

ip xfrm monitor state monitoring for xfrm objects

The xfrm objects to monitor can be optionally specified.

If the all-nsid option is set, the program listens to all network namespaces that have a nsid assigned into the network namespace were the program is running. A prefix is displayed to show the network namespace where the message originates. Example:

[nsid 1]Flushed state proto 0

Releases

8 releases since Debian 7 (Wheezy); the text changed 7 times.

  1. 7
  2. 8
  3. 9
  4. 10
  5. 11
  6. 12
  7. 13
  8. Arch