divaload8

Configure eicon diva active isdn card

Usage

divaload controller protocol [options]

Overview

divaload is used to setup the Eicon Diva card for the proper configuration.

Options

controller: selects the controller (card). This can be either:
-c n
where n is the controller number, or
-all
to operate on all cards.

protocol: can be one of the following:

-f 1TR6 Germany, old protocol for PABX................ PRI & BRI -f ETSI DSS1, Europe (Germany, ...)................... PRI & BRI -f FRANC VN3, France, old protocol for PABX............ PRI & BRI -f BELG NET3, Belgien, old protocol for PABX.......... PRI & BRI -f SWED DSS1 with CRC4 off, Sweden, Benelux........... PRI -f NI NI1, NI2, North America, National ISDN........ PRI & BRI -f 5ESS 5ESS, North America, AT&T..................... PRI & BRI -f JAPAN Japan, INS-NET64.............................. PRI & BRI -f ATEL ATEL, Australia, old TPH1962.................. PRI & BRI -f US North America, Auto Detect.................... BRI -f ITALY DSS1, Italy................................... PRI & BRI -f TWAN DSS1, Taiwan.................................. PRI & BRI -f AUSTRAL Australia, Microlink (TPH1962), On Ramp ETSI.. PRI & BRI -f 4ESS_SDN 4ESS Software Defined Network................. PRI -f 4ESS_SDS 4ESS Switched Digital Service................. PRI -f 4ESS_LDS 4ESS Long Distance Service.................... PRI -f 4ESS_MGC 4ESS Megacom.................................. PRI -f 4ESS_MGI 4ESS Megacom International.................... PRI -f HONGKONG Hongkong...................................... PRI & BRI -f RBSCAS Robbed Bit Signaling, CAS..................... PRI -f QSIG QSIG, Intra PABX link protocol................ PRI & BRI

The following options may be given to divaload.

-e [1,2,3]: set Layer 1 framing on PRI Adapter

1 - doubleframing (NO CRC4)
2 - multiframing (CRC4)
3 - autodetection

-x: set PRI Adapter in NT mode; default mode is TE

-z: set PRI Adapter in High Impedance state until first user application does request interface activation

-l [1...30]: set starting channel number on PRI Adapter. By default the allocation of channels is made on a high-to-low basis. By specifying -l you select a low-to-high allocation policy (in addition)

-q [0..3]: select QSIG options

0 - CR and CHI 2 Bytes long (default)
1 - CR 1 byte, CHI 2 bytes
2 - CR is 2 bytes, CHI is 1 byte
3 - CR and CHI 1 byte
(CR - Call Reference, CHI - B-Channel Ident.)

-n [0...20]: select NT2 mode and default length of DIDN (DIDN - Direct Inward Dial Number)

-o: turn off order checking of information elements

-p [1,2]: establish a permanent connection (e.g. leased line configuration)

1 - TE <-> TE mode, structured line
2 - NT <-> TE mode, raw line

-s [0,1,2,3]: D-Channel Layer 2 activation policy on BRI Adapter

0 - On demand
1 - Deactivation only by NT side, preferred, default
2 - Always active
3 - Always active, mode 2

-t [0...63]: specifies a fixed TEI value (Default is a automatic TEI assignment)

-u: select point to point mode on BRI Adapter; uses default TEI '0', NT2 mode is on

-[1...8]oad|osa|spid: BRI Adapter B-Channel options Specify the Originating Address (OAD), Originating Sub-address (OSA) and/or Service Profile Identifier (SPID) for each B-channel (1 or 2 by BRI, 1...8 by 4BRI)
Example: -1oad 123456 -1spid 1234560001

-d: display protocol options summary

-w: select alternative protocol code directory.
default directory: "/usr/share/isdn"

-h or -?: help

Releases

Unchanged in 9 releases since Debian 3.0 (Woody).

3.0–10